Polaris Pool Sweep bag for 180

Wrong Polaris Debris & Leaf Bag Saved Me About $30

Wrong Polaris Debris & Leaf Bag Saved Me About $30

I asked my daughter to buy me a Polaris debris and leaf bag for our model 180.  Well, I thought our model was 180 because the people who we purchased the house included some documents of items included with the purchase of the house.  We were given quite  few documents for the pool equipment.  When the bag arrived, I noticed that it was incorrect. It was missing the quick connect plastic ring clips.  It only had Velcro, no clips.  The Polaris 280, 480 and 3900 use “tear drop” shaped clips to secure the bag to it’s cleaners.

The image shows the “incorrect” bag for our pool sweep. It is missing the quick connect clips and the top bag zipper. Not that that bag has a rather long connection collar. I had to cut my 2 inch PVC pipe long enough to go up the full distance of that collar which is about 4 inches.

The bag shipped to us did not have quick clips to attach the bag to the pool sweep.  It was also missing a zipper at the end of the bag to allow quick removal of the debris and leafs.  I then discovered that my daughter did purchase the correct bag for a 180 model.  We must have had a newer model and the prior home owners failed to include that model in the documents given to us.  This new bag is way cheaper, costing close to $13 while the proper bag for our pool sweep costs just over $45.  I decided to find a way to make this cheaper bag work.  It was easy.  I removed the old ruined bag from the fitting by using screwdrivers to pry out the outside ring.

This image shows the concept for this project. The bag is at the top. Into the bag is a 2 inch PVC pipe cut to 4 inches so it extends up into the bag . I found that the bottom of this pipe did not have to be glued into the bottom parts as it fit very tight. The bottom parts consist of the old bag clips and a 2 inch PVC coupling had been inserted into the bag clip portion. Later, I would use irrigation primer and glue to marry the bag clip to the union.

I discovered that a 2 inch PVC irrigation pipe joint fit rather perfectly into the top of the part that clips to the pool sweep.  It was a bit slack but the irrigation glue should fix it in place.  I wanted to maintain the largest opening for leaves to pass upward into the bag.  I measured the diameter of the bag and it was close to the 2 inch pipe diameter.  I then cut  an irrigation pipe that slips into the 2 inch joint for a distance of 4 inches because the bag has a rather long stiff collar with a long side slit.  I wanted all the debris and leaves to go up into the bag and not slip out of that side collar opening, which is the reason for the rather long, 4 inch pipe length.

This image shows the full complete modification. The new bag slips down from the top, over the top ring and ends at the 2 inch union. The long pipe length was needed to ensure debris would pass completely into the bag. Note that a ring (not seen in this image) has been removed from the bottom clip part so as to not interfere with the new bag. I had to remove the prior ruined bag which was locked in place by a hard to get off ring. If you want to save time, just cut the old bag with a sharp knife or razor saving you form removing the outer ring, which is a pain to get off.

I decided upon 4 inches because the bag has a rather long throat and I wanted the pipe to go up into the bag.  I was worried that the bag just might slip out of the plastic pipe upward.  I needed a solution to that problem.  I found an old 2 inch PVC joint and cut just a little off of it.  I then glued that small ring to the top of the 4 inch pipe to the bag would not slip off.

The above image shows the completed new construction.

This pools sweep modification PVC parts cost less than $5 for new parts.  The correct bag would have cost about $45. The new bag, my daughter purchased cost only about $13.  In just under 2 hours I had created a modification to the pool sweep that saved me just over $30.

The problem with the above bag is when you remove it from the sweeper, the contents of the bag can easily fall out.  Also, the bag does not hold much and fails to collect that much pool debris.  The next option, described next, is recommended.

A much better solution is to buy a really good cheap bag.  I recommend this bag:

SuMile 2 Pack All Purpose Bags Nylon Mesh Zipper Bags Pool Cleaner Bags Replacement Bags for Polaris 280, 480 Pool Cleaner Replacement Parts K13 K16

You get two bags for a very reasonable cost.   I find them to be very good construction and do a perfect job of collecting the pool debris.  This bag holds a lot.  I love the zipper for opening the bag and removing the contents.

 

Updated: May 30, 2019